#Ampps closes without opening mac pro

# User/Group: The name (or #number) of the user/group to run httpd as. # httpd as root initially and it will switch. # If you wish httpd to run as a different user or group, you must run # with ServerRoot set to '/php/libphp5.so # with '/', the value of ServerRoot is prepended - so 'logs/foo_log' # of the server's control files begin with '/' (or 'drive:/' for Win32), the # Configuration and logfile names: If the filenames you specify for many # Do NOT simply read the instructions in here without understanding # for a discussion of each configuration directive. # configuration directives that give the server its instructions. # This is the main Apache HTTP server configuration file. ScriptAlias /cgi-bin/ '/Applications/AMPPS/'/Applications/AMPPS/apache/logs/'ĬustomLog '/Applications/AMPPS/apache/logs/' combined Ive checked the vhosts conf and it looks fine and there is a line in the hosts table. Localhost works and so do all the AMPPS admin bits. I create a domain but when I go to access it in a browser the connection is refused. in case SMC reset does not solve your problem you should consider a more thoroughly inspection of your battery.įrom experience I can say that a screwed up SMC can put excessive stress on a battery and destroy it in a very short time.I have installed AMPPS for MAC, it's a straight out of the box installation.does it charge? What does the MagSafe LED say: green, orange, off?.

check all the connections, what is the condition of your battery? Is it starting to increase its volume? Do you have a stable power connection at power outlet or at the MagSafe?.

When your MagSafe connection works you should get proper feedback from the LED. A SMC reset + MagSafe cleaning helped in our case, but we will probably have to buy a new power adapter. In our case the MBP stopped holding charge and did not charge. A screwed up SMC could be at the cause of all your troubles and in that case the question is: why did it screw up?

#Ampps closes without opening mac pro

If, for example your MagSafe connection is not stable, your SMC could get into trouble: are all the pins ok or is one stuck? This happened to a MacBook Pro we have and as a result we had to buy new Batteries continuously until we found out, that the pins apparently did not have a stable connection. The other two answers already explain everything you need to know about each of those steps very well.īut you should also check all the components and connections your current passes through: power adapter, MagSafe connection pins, MagSafe connection at your laptop. Try resetting SMC first and only after a SMC reset did not solve your problem you should think about replacing your battery. Start inspecting all the different components involved. Your MBA will now be able to hold a charge like it did when new. Make sure you note where each screw comes from as they are different. Don't yank it off, use a spudger or similar tool to disconnect the molex connector by 'wedging' it off. Just be careful when disconnecting the battery from the logic board. Then, just remove the screws holding in the battery and swap. Just remove the screws holding the back cover in place. To replace the battery it's actually very simple. Definitely avoid the ones with less than a 12 month warranty no matter how inexpensive they are. From personal experience, the more 'warranted' batteries lasted much longer.

You just need a new replacement battery battery (I suggest getting ones with at minimum a 12 month warranty 18 month is better). If we unplug the power adapter, the battery has nothing to supply so the computer shuts off. (Coincidentally, I have a MBP with the exact same symptoms you have, so the output here works perfectly!) The key here is that under 'Amperage' we get a '0' which means there is literally no current coming from the battery (Note: even though it may have voltage, if there are no amps, it won't have the 'power' to supply). Here we can see that the battery is in need of service. You can limit it to just the battery info by tweaking the command as follows: $ system_profiler SPPowerDataType | grep -i 'charge information' -A 10 The output can be rather lengthy the info you need will be at the top. That will give you all the power settings related to your Mac. Using Terminal, just issue the command: $ system_profiler SPPowerDataType These are all good, but in my opinion, I would much rather use built in tools to get this info. There are a number of utilities that you can get (paid and free) that will look at your battery status: If it's necessary to have the power adapter plugged in when trying to turn it on, it's a sure sign that the battery is discharged. The computer (in this case your MacBook Air) turns off because there is no more/not enough charge in the battery.